# How do you measure ultra-low impedance in PCB power distribution networks?

**URL:** <https://sierraconnect.protoexpress.com/t/how-do-you-measure-ultra-low-impedance-in-pcb-power-distribution-networks/4578>\
**Category:** Today's Discussion\
**Tags:** impedance\
**Created:** [October 14, 2026, 3:10pm UTC](https://sierraconnect.protoexpress.com/t/how-do-you-measure-ultra-low-impedance-in-pcb-power-distribution-networks/4578 "2026-10-14T15:10:34Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Mohamed\_Faheemuddin](https://avatars.discourse-cdn.com/v4/letter/m/4da419/32.png) [@Mohamed\_Faheemuddin](https://sierraconnect.protoexpress.com/u/Mohamed_Faheemuddin)\
**Post date:** [October 14, 2026, 3:10pm UTC](https://sierraconnect.protoexpress.com/t/how-do-you-measure-ultra-low-impedance-in-pcb-power-distribution-networks/4578/1 "2026-10-14T15:10:34Z")

</div>

Measuring ultra-low impedance in a power distribution network (PDN) can be challenging, especially at high frequencies. The 2-port shunt-through method is commonly used for these measurements, but ground loops and cable losses can introduce errors, particularly when measuring impedances in the micro-ohm range.

I wanted to start a discussion on practical approaches for making accurate ultra-low impedance measurements.

 ![2-port shunt-through impedance measurement setup using the Keysight E5061B VNA and the Picotest ground isolators J2102A-J2113A.](https://global.discourse-cdn.com/sierraconnect/original/1X/3b4d362f8e266195d33e8520ae3000089e681eec.png)

---

<div class="post-metadata">

**Author:** ![Mohamed\_Faheemuddin](https://avatars.discourse-cdn.com/v4/letter/m/4da419/32.png) [@Mohamed\_Faheemuddin](https://sierraconnect.protoexpress.com/u/Mohamed_Faheemuddin)\
**Post date:** [October 14, 2026, 3:10pm UTC](https://sierraconnect.protoexpress.com/t/how-do-you-measure-ultra-low-impedance-in-pcb-power-distribution-networks/4578/2 "2026-10-14T15:10:48Z")

</div>

The 2-port shunt-through method measures impedance by analyzing the transmission coefficient (S21) through the device under test. However, the instrument grounds and test cables can create an additional current-return path, introducing errors in the measured impedance.

Minimizing this common-mode current is essential for accurate results, particularly when measuring ultra-low impedances.

---

<div class="post-metadata">

**Author:** ![Mohamed\_Faheemuddin](https://avatars.discourse-cdn.com/v4/letter/m/4da419/32.png) [@Mohamed\_Faheemuddin](https://sierraconnect.protoexpress.com/u/Mohamed_Faheemuddin)\
**Post date:** [October 14, 2026, 3:11pm UTC](https://sierraconnect.protoexpress.com/t/how-do-you-measure-ultra-low-impedance-in-pcb-power-distribution-networks/4578/3 "2026-10-14T15:11:35Z")

</div>

A few factors are important when setting up these measurements:

- Minimize ground-loop errors: Use a suitable ground isolator to reduce common-mode current in the measurement setup.
- Use high-quality cables and probes: Cable losses and inadequate shielding can affect measurement accuracy.
- Verify the setup: Measure a known resistance to confirm the measurement setup, and use a four-wire Kelvin measurement to verify very low DC resistance.

The appropriate isolation method depends on the required impedance range and measurement frequency.

---

<div class="post-metadata">

**Author:** ![Mohamed\_Faheemuddin](https://avatars.discourse-cdn.com/v4/letter/m/4da419/32.png) [@Mohamed\_Faheemuddin](https://sierraconnect.protoexpress.com/u/Mohamed_Faheemuddin)\
**Post date:** [October 14, 2026, 3:12pm UTC](https://sierraconnect.protoexpress.com/t/how-do-you-measure-ultra-low-impedance-in-pcb-power-distribution-networks/4578/4 "2026-10-14T15:12:25Z")

</div>

For measurements as low as 20 µΩ, the test setup itself can significantly affect the results. The Picotest J2102A common-mode transformer supports measurements at and above 20 µΩ, with an operating frequency range starting at approximately 100 Hz. The J2113A semi-floating differential amplifier can be used for measurements at and above 1 mΩ, including down to DC.

Selecting the isolation method, cables, and probes based on the required measurement range helps reduce errors when characterizing a PDN.

Of course, the best approach depends on the impedance range, frequency of interest, and available test equipment.

For a detailed explanation of the measurement technique and ways to minimize ground-loop errors, check out this article:

[Ultra-low Impedance Testing Using the 2-Port Shunt-Through Measurement Technique](https://www.protoexpress.com/blog/ultra-low-impedance-testing-using-the-2-port-shunt-through-measurement-technique/).